The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The…
Brand:
Cambium Networks
Code:
ART-152748
MPN
SFP-10G-SR
EAN
5704174389774
The SFP+ SR module electrical interface is compliant to SFI electrical specifications. The transmitter input and receiver output impedance is 100 Ohms differential. Data lines are internally AC coupled. The module provides differential termination and reduce differential to common mode conversion for quality signal termination and low EMI. SFI typically operates over 200 mm of improved FR4 material or up to about 150mmof standard FR4 with one connector. The transmitter converts 10Gbit/s serial PECL or CML electrical data into serial optical data compliant with the 10GBASE-SR standard. An open collector compatible Transmit Disable (Tx_Dis) is provided. A logic “1,” or no connection on this pin will disable the laser from transmitting. A logic “0” on this pin provides normal operation. The transmitter has an internal automatic power control loop (APC) to ensure constant optical power output across supply voltage and temperature variations. An open collector compatible Transmit Fault (TFault) is provided. TX_Fault is a module output contact that when high, indicates that the module transmitter has detected a fault condition related to laser operation or safety. The TX_Fault output contact is an open drain/collector and shall be pulled up to the Vcc_Host in the host with a resistor in the range 4.7-10 k?. TX_Disable is a module input contact. When TX_Disable is asserted high or left open, the SFP+ module transmitter output shall be turned off. This contact shall be pulled up to VccT with a 4.7 k? to 10 k? resistor The receiver converts 10Gbit/s serial optical data into serial PECL/CML electrical data. An open collector compatible Loss of Signal is provided. Rx_LOS when high indicates an optical signal level below that specified in the relevant standard. The Rx_LOS contact is an open drain/collector output and shall be pulled up to Vcc_Host in the host with a resistor in the range 4.7-10 k?, or with an active termination. Power supply filtering is recommended for both the transmitter and receiver. The Rx_LOS signal is intended as a preliminary indication to the system in which the SFP+ is installed that the received signal strength is below the specified range. Such an indication typically points to non-installed cables, broken cables, or a disabled, failing or a powered off transmitter at the far end of the cable.
S+31DLC10D is a 10G SFP+ transceiver with a LC connector, 1310nm, for up to 10 kilometer Single Mode…
Brand:
MikroTik
Code:
ART-155178
MPN
XS+31LC10D
EAN
-
S+31DLC10D is a 10G SFP+ transceiver with a LC connector, 1310nm, for up to 10 kilometer Single Mode fiber connections Units are tested and compatible with CCR1036-8G-2S+ and CCR1036-8G-2S+EM. Units are compatible with non-MikroTik SFP devices as well.
Multi-mode, duplex, fiber transceiver module. The 10 Gbps Multi-mode Optical Module is a duplex…
Brand:
UBIQUITI
Code:
ART-152199
MPN
UACC-OM-MM-10G-D-2
EAN
0810010076908
Multi-mode, duplex, fiber transceiver module. The 10 Gbps Multi-mode Optical Module is a duplex transceiver that delivers up to 10 Gbps speed over distances up to 300 meters.
Single-mode, simplex, fiber transceiver module. The 1 Gbps Bidirectional Single-mode Optical Module is a simplex transceiver that delivers up to 1.25 Gbps speed over distances up to 3 kilometers.
Multi-mode, duplex, fiber transceiver module. The 1 Gbps Multi-mode Optical Module is a duplex…
Brand:
UBIQUITI
Code:
ART-152198
MPN
UACC-OM-MM-1G-D-2
EAN
0810010076922
Multi-mode, duplex, fiber transceiver module. The 1 Gbps Multi-mode Optical Module is a duplex transceiver that delivers up to 1.25 Gbps speed over distances up to 550 meters.
SFP+ to RJ45 transceiver module that delivers 10 Gbps speed via a converted Ethernet connection. The…
Brand:
UBIQUITI
Code:
ART-152230
MPN
UACC-CM-RJ45-10G
EAN
0810010077028
SFP+ to RJ45 transceiver module that delivers 10 Gbps speed via a converted Ethernet connection. The 10G SFP+ to 10GbE RJ45 Module is a RJ45 transceiver that can be inserted into an SFP+ port in order to connect a copper Ethernet cable. Use this SFP+ to RJ45 module to deliver 10 Gbps speed over Ethernet connections spanning up to 30 meters.